DIY Home Improvement Forum banner

inducer

  1. Furnace Short Cycling

    HVAC
    My furnace is "short cycling" I believe. Typically the blower will turn on for about a minute and then shut off. After that I can hear the inducer motor running for a few minutes and then the blower kicks on for a normal amount of time to complete the cycle. There have been a couple of times...
  2. Pressure Switch Stuck Open, Inducer Doesn't Start, Blower Motor Does Start

    HVAC
    Hey Gang, First time poster here. Went to fire up the heat for the first time this season yesterday, and after 30 minutes I noticed it had been blowing the whole time, but there was no heat. This is a model number GUI075A012AIN. Taking a closer look, I saw that I had three blinking lights...
  3. Inducer Motor Install

    HVAC
    I am installing my own inducer motor and noticed the new fan has 3 ports on it, two large ones and one small one. The existing tubing I have doesn't fit the larger ones but fits the smaller one. Am I allowed to use the smaller one for the limit switch tubing as long as I plug the larger two...
  4. Goodman GMS8 Furnace Inducer vacuum failimg

    HVAC
    Hi, I'm an engineer and have some technical know how. I will say upfront I have not exhaustively searched all the threads on this furnace. I have a GMS8 furnace, vertical, natural gas, single stage, about 10years old. It started as an intermittent problem, of the furnace starting up, the...
  5. No power to Inducer

    HVAC
    He guys/gals, My heater stopped working a week ago. Its a 2008 honeywell system. AC works fine. Main blower come on with heat request. heat sequence never starts. Pressure switch is fine. But the inducer never starts. I powered the inducer straight to a 120v plug and it runs fine, no bearing...
  6. Luxaire Furnace Inducer fan will not start.

    HVAC
    This summer I had flooding in my basement. The furnace was damaged. The inducer fan and control board were replaced. It worked fine for several months. It recently stopped working again. The error code is 3 flashing lights indicating pressure switch stuck open. When disconnecting the...
  7. GMNT80-4 Inducer Motor failing.

    HVAC
    The inducer motor on a 13 year old GMNT80 furnace cuts out intermittently after about 10 min of run time. It only falls out for a second, which in turn cuts out the gas valve. then the ignition process starts over, has no problem lighting again, and about 5 minutes later, motor stops again...
  8. One week old Lennox EL296V inducer motor housing full of water

    HVAC
    Just had a Lennox EL296V installed last week and the inducer motor is making weird noise and water is leaking out of the motor housing, I searched the forum, some suggested the drain trap be cleaned, however, I can see water draining to the floor drain when heat is on ... any idea? did the...
  9. Draft Inducer Motor Assembly

    HVAC
    I am looking for the part number for a Draft Inducer Motor Assembly. My furnace is a Carrier Weathermaker SX, Model Number 58SXA120--101LG, installed in Novemer 1991. The inducer motor part number is JA1P077N, 115Vac, 60Hz, 1.75A, 3300rpm, 0.050hp. The motor is running hot and I want to replace...
  10. Gas furnace overheating problem with two solutions - which one is better??

    HVAC
    Hi there, thanks for reading this thread. We have a 15 years old Day&Night gas furnace that has been working fine until now. For some reasons over the past two weeks, the unit (furnace) became so hot that it would just shut down by itself, which we will have to then go to the basement and...
  11. Error Code 31 Payne, Help

    HVAC
    My Payne furnace is toast. The board lights up with code 31. I noticed that there are two fan motors, One small one, and One big one. The Big fan starts first works for about 2 minutes then shuts off. Then the small fan starts spinning and nothing happens after that. I was told that some...
  12. Carrier 58STA/58STX No Heat

    HVAC
    Tried to use the furnace for the first time this season and our furnace will not start (North Texas and damn good insulation). I am leaning towards the control board, but I will detail my troubleshooting and would appreciate any additional advice. The thermostat calls for heat, but I get a 31...
  13. Replacing Fasco 7062-3136 draft inducer blower on my Bryant Gas Furnace

    HVAC
    Hi, I found this thread on this site from back in 2006: http://www.diychatroom.com/f17/replacement-inducer-blower-4684/ My circumstances are very similar. I have Bryant 349M horizontal gas furnace with a Fasco 7062-3136 type U62B1, p/n 240101 OH92, 3450 rpm, class B, 115v, 60H, .70A inducer...
  14. Bradford White Water Heater (50 gal) not working - might be blower?

    Plumbing
    10+ yr old Bradford White water heater stopped working. 1 plumber said the blower/motor is broken. Current blower motor is Jackel #117524-00 and 1150519-00. Getting all sorts of advice as I assess who should fix this - does it require an HVAC specialist? can a general plumber fit it? Parts also...
  15. Nice cold air but no circulation?

    HVAC
    I just purchased my first home. We have been installing hardwood floors and such. The weather recently hit the 90's. Air worked fine at first but now will not circulate. I have a Lennox system- M/N: G23Q314-160-6. I thougt we might have run it to low trying to cool the place off or that the...
  16. Pressure switch stuck open? 2 areas im looking @

    HVAC
    Hi, I've been searching for a few days & am unable to find what I'm looking for. I have a 7 year old furnace. lennox ultra 5 advantage. Went to turn on heat & nothing!! The led trouble code is 3 blinks = "Pressure switch stuck open 30 seconds or longer after call for heat. on/off switch...
Top