Search Results for ‘flame sensor’

I changed the furnace filter and put in a new flame sensor because the furnace was making a slight jerk sound (only once through the whole cycle), and I want to know what is making that slight jerking sound? Everything seems to be running okay with the furnace. Could my problem be the new flame...

I NEED HELP!!! I have a rheem furnace and everything works in sequence like its supposed to except when the burners kick on 4 seconds later they kick right back off and restarts the cycle until going into lockout which i get 1 continuous green flash on “ok” led. Things ive tried: Changed flame...

I have a Maytag gas furnace (sorry, not sure of model, but its newer high efficiency kind) and its started short cycling. When the thermostat commands heat, the furnace draft fan will start, then the igniter comes on, then gas starts and flame is instant, but then the gas cuts off in 1-2...

I have an issue with my furnace (Goodman GDT090-4B). Very early this morning I could hear it short cycling. I immediately thought gas valve, because the blower was running, the ignitor would glow, and after the click, I would not hear gas coming on. So furnace would not light, and the process...

I have a Rheem Furnace model RGPH-07EAUER, serial # DF5D302 F1295 5487 Around December 2017, I started having issues with the burners going out. I cleaned and even replaced the flame sensor, and I also cleaned, and sanded the burners and the chassis area around the burners, yet no love...

Winter is coming and many people will find themselves in a situation where the furnace turns on and then shuts off soon after. Usually this is due to the flame sensor getting dirty or malfunctioning. It is an easy fix. In this video, I show you had to clean it (fixes the problem 90% of the time)...

Furnace: Keeprite, 15 year old, Honeywell Q3400A1024 flame sensor/igniter module, Honeywell gas valve. Problem: blower activates, igniter turns yellow, pilot flame lights up, main burners light up, keep burning for 10-20 seconds and flame out, then after a while ignite again, and flame out...

My 5-year old high-efficiency ICP furnace won't stay lit with the burner panel on. With the panel on, I look through the little window, and the last burner (where the flame sensor is) flickers and then goes out after 30-60 seconds. The fan keeps going and it cycles through that way a few times...

Hi, I have the Trane XE80. I have a few flame sensor questions: 1. Does this appear to be the correct replacement: http://www.amazon.com/gp/product/B00ECEENHG/ 2. That flame sensor angles a bit differently than the original, is it ok as long as the flame hits it some place? 3. The furnace...

I have a 1997 vintage Trane XE80, which would cycle on for heat, Gas burners will light but for only a second or two then go off. The unit has a White Rogers Model 50A50-471 controller, The controller is flashing error code 5: Flame Sensed with Gas Valve Off. After reviewing post on this...

I have a G43UF Lennox heater (6 years old). Two weeks ago, it began shutting off (after 20-30 sec) for the 3 cycles then getting the alternating red/green lights. So I replaced (NEW) the "Flame Sensor", "Ignitor", and cleaned the burner unit. The heater now stays on for 10+ min but eventually...

Events to date: *Resolved possible drainage issue *Replaced filtrete filter with low resistance permanent filter (about 5 days ago). **These resulted in unit working fine for about 5 days, but issues starteed again today. *Have cycled the furnace about 5 times today. Previously, only saw code...

I've got an older Payne/Carrier 395BAW024060 inside furnace. Last year, I had trouble with the flame sensor (don't remember symptoms) which I was able to solve by removing it and cleaning it thoroughly with steel wool. I started up the furnace for the first time last week, and it ran fine, but...