DIY Home Improvement Forum banner
board
1-18 of 20 Results
  1. Electrical
    Hello, To begin, I know nothing about electrical other than how to connect wires. So my old Essick Air humidifier decided to fry it's board, but luckily I found a replacement board online. Unluckily, the replacement came with no diagrams, and has a different setup. The old one [image 1] had...
  2. Appliances
    GE GTW680BSJ0WS I had the 2 water supply valves turned off when I started the washer. Got the “H2O Supply” message on the display. As usual, I turn off washer, turn on water, turn on washer; and all is good. But, this time: The control panel does not respond to any buttons, the water pump...
  3. Flooring
    I have a single floor board that is peaking (please see pictures). I am not sure what type of material or the method that was used to install it. What is the best way to fix the board?
  4. HVAC
    hello i currently have carrier confortzone II with a carrier board. I want to replace them. I already bought 3 nest. 3 zones + 1 external compressor. here are the pics and the connections on the board: -------- safety sensors: - outdoor air temperature - leaving air temp - heat pump temp...
  5. HVAC
    I need to replace a discontinued control board from an Amana air handler. 1/3HP 230VAC fan motor. 3x4.75W resistance heat coils. Is there a generic or universal control board available? Amana p/n 20305401 from model BMA36F00A
  6. HVAC
    Hello all, Needing a bit of help here. I've got a Ducane furnace that was installed in 2007. Lately is has started having an intermittent startup failure. When I call for heat, there is a what sounds like a relay click from somewhere inside, and NOTHING else. The heartbeat light on the...
  7. Windows and Doors
    Hi there, I'm wondering if there is a preferred type of material for affixing decorative exterior shutters to Hardie Board siding. Does it matter? I'm looking at these ones from Home Depot - https://www.homedepot.ca/en/home/p.15-inch-x-60-inch-paintable-louvered-shutters.1000427076.html...
  8. HVAC
    Towards the end of last summer I was given a central AC unit. I had a friend of my dad (certified HVAC technician) install the unit. He supplied everything for the install, including thermostat (honeywell programmable). I remember in the process of the install he thought he may have to put a new...
  9. General DIY Discussions
    Hello Everyone - I'm hoping to get some ideas. I'm refinishing my basement and looking for alternatives to drywall. The basement previously had 1/8" paneling directly against the studs, which I believe is now a code violation. I'm not sure whether there is any paneling or wall panels that can...
  10. HVAC
    Hi, I have a Bryant 80+ furnace (with AC) and my board is continually flashing. The status code says reversed polarity. Can anyone help me figure out what is going on before I have to call a HVAC company. I have little experience with furnaces but am good with electricity. Thanks in advance!!
  11. HVAC
    Hi, we came home on Christmas Eve to a burning plastic smell in the house. Thought it was the Christmas tree, so I unplugged it, ventilated the house, and we went to bed. Next morning, got up, heat wasn't working and the smell was back. Traced it back to the control board on the (natural...
  12. HVAC
    Hello folks, I recently had to replace the control board on my furnace. (N9MSB) The board I purchased is identical to the original. (OEM 1184594) I received it in a new, unopened condition. No physical defects to be seen.. So I swapped the board out and took it for a spin.. I ran it through a...
  13. Kitchen & Bath Remodeling
    Hi, I just got a quote from a contractor to level out my floor. His method of leveling out the floor is.. 1. Install 1/4 underlayment to shim and level out floor. 2. Install cement board to provide a level surface. He's charging $465 for this. Does this sound like a good way to do this and a...
  14. Remodeling
    I had a contractor move our boiler located inside the house right behind the guest bathroom to the garage. The new space will be converted to a linen closet. The knocked down the old drywall and i'm ready to install new drywall but i'm stuck with the following question. Should i install Cement...
  15. Building & Construction
    I have a 50 yr old house w/board & batten siding. It has a substantial carport w/the same siding. I want to put up a 3rd wall on the carport and roughly match the siding. The original battens are 5/8" thick and 2 3/4" wide. The only lumber I can find that thickness are short specialty boards for...
  16. Remodeling
    Can some of you pros out there give me some insight on how to prep shower walls to be tiled? I always read that a cement backer board is the way to go. But yet every time I walk into a new home under construction by a variety of builders, they are using green board or blue board under the...
  17. Building & Construction
    A tiled Kitchen Island Counter with 10" - 12" projection. Tile Prep. Know How. We are getting ready to finish our Kitchen Tiling and need to lay some backer material for my 4"x4" white tile. We have a chair rail detail for the edge and need to build up a base 1 1/2" thick. I have thought...
  18. Building & Construction
    What is the best way to build a fire rated wall assembly? Good question... I have been looking into just this the past 36 hours and have found many options. Which one is the best? Looking for answers...
1-18 of 20 Results
Top