I am plumbing a new shower assembly and I am having trouble soldering the brass flange to the copper pipe which will connect to the valve assembly. I managed to get the pipe hot enough to melt the solder but the flange didn't adhere to the pipe and i was able to slide the flange off the pipe. What am I doing wrong?
Also, should I be concerned about over heating a copper pipe when soldering on copper fittings like elbows? In my concern to insure I had the joint soldered, I heated it for quite a bit and it began smoking...burning the flux I guess.
Maybe you got oil and/or not enough heat to brass fitting?
I would sand both the inside of a brass fitting and outside of a copper pipe (open mesh sandpaper works best), apply flux to both, joined them together, then apply heat and solder.
Remember to apply heat to the brass fitting, not the copper pipe. When you have enough solder covering the entire joint, solder will start to drip out. Stop and wipe the fitting area with a dry rag (not wet).
I used to generate tons of recyclable metal fittings until I figured out the brass needing more heat part Just take a deep breath and take your time.
Good luck
PS. I usually wear a pair of latex gloves when sanding and applying flux to prevent hand oil from getting on those parts.
soldering brass fittings is the same proceedure as copper but what are you calling a flange?
If you're working with a shower valve, be sure to remove the guts prior to applying heat. You can damage the o rings,etc.
Are you using flux? What kind? Perhaps you're not heating the brass enough. Heat the fitting and not the pipe.
And yes, you can overheat the fitting and ruin the flux but it will always smoke.
Take a few minutes and watch some youtube soldering videos
It was labelled a flange in the store but I think it might be something else. One end is a 1/2 inch pipe and the other end is a female thread that will thread onto the shower valve. I am replacing all of the pipe so, I have been assembling it so that I can attach the 'flange' to the pipe and thread it on to the valve and then complete the other solder joints...this way, I don't have to worry about ruining the valve rings, etc.
The brass fitting was looser on the pipe, prior to soldering, than the copper fittings were. I assume the joint should fill with solder even though it was looser.
I think I spent more time heating the copper than the brass to begin with, but I corrected this and the solder was entering the joint but not causing the two pieces to become one.
The flux I am using is Kester acid paste flux sp-30. I was heating the pipe but, after reading some advice, I started heating the fitting and I have been successful. Tomorrow I hope to hook the shower assembly into the line and see how it works. Crossing my fingers for no leaks.
you may want to do a simple leak test before putting up durock.
when i worked on my bathrooms, I used something like this to plug into your threaded ends (use some white teflon tape for a tight seal) and test them individually.
I think Home Depot has it under "Watts 1/2 in. Brass Square-Head Pipe Plug". It is pricey at 5 bucks each but you will know that your soldered fittings are leak proof.
you may want to do a simple leak test before putting up durock.
when i worked on my bathrooms, I used something like this to plug into your threaded ends (use some white teflon tape for a tight seal) and test them individually.
I think Home Depot has it under "Watts 1/2 in. Brass Square-Head Pipe Plug". It is pricey at 5 bucks each but you will know that your soldered fittings are leak proof.
I was thinking that I could solder the last two connections to finalize the install and then just turn the water on to check for leaks. Should I be doing something different? I am not sure how using a plug would be different.
With the assembly I have, I should be able to turn on the tap itself to see what happens. I would just be using the shower head to spray water in the drain. The cbu would go up after.
Two steps forward and one step back. I have the shower assembly pretty much ready to go but, the water shut off valves were stuck. The hot water valve is now working properly and the cold water valve is still being worked on.
Okay, I turned the water on to test my plumbing and there are no leaks woohoo and I am relieved. But, how long should I wait to to be certain that my plumbing is good or is it unlikely that anything will begin leaking now?
My solder joints are not pretty and I am slow but, it seems to be good.
Two types of solder leaks- one sprays a little pisser stream
The other seeps very slowly.
Although you can tell almost instantly, wipe your joints with a paper towel after a couple hrs. If no moisture your good to go
Thanks eplumber. I have the joints wrapped with toilet paper now to see if I get any moisture. If I do get a leak, what is the method for fixing a joint? Do I just heat it again and add solder?
Thanks eplumber. I have the joints wrapped with toilet paper now to see if I get any moisture. If I do get a leak, what is the method for fixing a joint? Do I just heat it again and add solder?
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Related Threads
?
?
?
?
?
DIY Home Improvement Forum
3.1M posts
319.6K members
Since 2003
A forum community dedicated to Do it yourself-ers and home improvement enthusiasts. Come join the discussion about tools, projects, builds, styles, scales, reviews, accessories, classifieds, and more! Helping You to Do It Yourself!